• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar

Authentic Automotive Product Reviewer & Adviser

  • Home
  • Auto Accessories
    • Cold Air Intake
    • Suspension System
    • Brake Rotors
    • Fuel Filter
    • Ignition Coil
    • Car & Truck Battery
  • Tonneau Cover
    • Car Cover
    • Floor Mats
  • Tires
  • DIY & Fix
  • Blog
Home » Auto Accessories

Top 5 Best Universal C Notch Kits for Lowered Trucks Review

Last Update: November 22, 2026 | Post By Patrick Jordan, BSc in Automotive Engineering Technology.
Chief Editor and Technical Writer at AutoExpro

Universal C notch kit for lowered trucks, welded step notch assembly

Drop a truck a few inches and the rear axle soon meets the frame. The ride turns harsh and the bump stops take a beating. A frame notch gives the axle room to travel, which is why most deep-drop builds need a universal C notch kit for lowered trucks.

Most notch kits arrive as laser-cut plates, not bolt-on parts. You cut the frame, fit the pieces, and weld them in. Steel thickness, step height, and boxing plates decide how strong the finished notch is. Cheap kits and good kits can look identical in photos, so specs matter more than listings.

We compared five Amazon kits on steel gauge, piece count, drop clearance, and honest fitment notes. Some suit deep, air-ride drops. Others only make sense for mild sport drops. Pick by how low you plan to go, then browse our truck upgrades guide for other mods worth pairing.

As an Amazon Associate, we earn from qualifying purchases. This costs you nothing extra.

🏆 Editor’s Top Pick

PIT66 10″ Tall Step C Notch Kit (16 Pieces)

 

10-inch tall step C notch kit plates for lowered truck frames

The PIT66 step kit gives the most documented drop clearance here: 8 to 9 inches in a typical install. Sixteen laser-cut pieces make up the full set, and it carries the only rating we could verify. Check your rail width before ordering.

  • 16-piece weld-on set
  • 10-gauge laser-cut steel
  • 10-inch tall, 2-inch wide step
  • 8–9 inch drop clearance

🛒 Check Price on Amazon →

⚡ Quick Picks

#1 Best Overall: PIT66 10″ Step Kit
#2 Best Heavy-Duty Steel: airmaxxx 8-Piece Kit
#3 Best 8-Inch Step: BALOCEO 8-Piece Kit
#4 Best for Sport Drops: Universal Mini 6-Piece Kit
#5 Best Entry-Level Mini: Labwork Mini Kit

Top 5 Universal C Notch Kit Reviews for Lowered Trucks

#1 BEST OVERALL

1. PIT66 10″ Tall Step C Notch Kit — Deep-Drop Step Notch

10-inch tall step C notch kit plates for lowered truck frames

★★★★☆
4.5 on Amazon (9 ratings)
Editor Score 9.0/10

The PIT66 is a 16-piece weld-on step kit cut from 10-gauge steel, a bit over 1/8 inch thick. The listing promises 8 to 9 inches of extra axle clearance in a typical install, which suits trucks sitting on the frame. It is thinner than the 5 mm kits here, so box the rails and weld carefully.

16 pieces
10 ga steel
10″ tall, 2″ wide
8–9″ drop

Key Features

  • 16-piece weld-on set — Laser-cut parts mean cleaner fit-up and fewer gaps when you tack the notch together.
  • 10-gauge steel — Over 1/8 inch thick, which is workable for notches but thinner than 3/16-inch plate.
  • 10-inch tall step — The tall profile leaves deep room for the axle to rise into the frame.
  • 2-inch wide notch — Measure your rail first, since this listing gives only the 2-inch version and no model-specific fitment.

Pros

  • Largest documented drop clearance
  • Only kit with a verified rating

Cons

  • Thinner steel than 5 mm kits
  • Fitment details are vague

What buyers say: An eBay buyer of a near-identical 10-inch step kit wrote, “Worked great for my project truck.”

🛒 Check Price on Amazon →

#2 BEST HEAVY-DUTY STEEL

2. airmaxxx Universal Weld-In C Notch Kit — 5 mm Plate

Weld-in C notch kit steel plates for slammed truck frames

No Amazon rating data verified yet
Editor Score 8.7/10

The airmaxxx kit packs eight CNC laser-cut plates of 5 mm steel, built for deep drops and through-the-bed setups. That gauge is the heaviest in this roundup, tied with one other kit. Planning air ride? Read about air suspension problems first, then expect to trim and shape the universal plates. It suits custom builds, not bolt-on swaps.

8 pieces
5 mm steel
Weld-in
Universal fit

Key Features

  • Eight-piece weld-in set — Complete plate set for a full notch, ready for cutting, fitting, and welding.
  • 5 mm laser-cut steel — Thick, precisely cut plates that weld cleanly and resist flexing on heavy trucks.
  • Built for slammed stances — The listing targets deep suspension drops and axle clearance on custom-built trucks.
  • Universal fit — Fits most pickups in theory; confirm frame rail dimensions before you cut anything.

Pros

  • Heaviest plate gauge here
  • Aimed at deep drops

Cons

  • No rating data seen yet
  • Welding skill required; no model-specific fit

🛒 Check Price on Amazon →

#3 BEST 8-INCH STEP

3. BALOCEO Universal 8-Piece C Notch Kit — 8″ Frame Step

Eight-piece weld-in C notch kit plates for custom dropped trucks

No Amazon rating data verified yet
Editor Score 7.9/10

The BALOCEO is another eight-piece weld-in kit in 5 mm steel, sold as an 8-inch frame step for custom drops. Listing copy is messy. It mentions a 5 mm drop length and describes axle repositioning, which sounds like a flip kit. Treat it as a notch kit only after confirming the contents, and message the seller first.

8 pieces
5 mm steel
8″ frame step
Bare metal

Key Features

  • Eight-piece weld-in set — Titled as a full C-notch kit with an eight-inch frame step for custom drops.
  • 5 mm steel plates — Matches the airmaxxx on gauge, so strength should be comparable if the cuts are clean.
  • Bare-metal finish — Listing says steel, bare metal, so prime and paint it after welding.
  • Universal fitment — Product overview claims universal fit but names no truck, so verify your frame first.

Pros

  • 5 mm plate thickness
  • Eight-inch step height

Cons

  • Confusing listing details
  • No ratings seen yet

🛒 Check Price on Amazon →

#4 BEST FOR SPORT DROPS

4. Universal Mini C-Notch Kit, 6-Piece — Mild Drops

Universal mini C notch kit for sport dropped trucks

No Amazon rating data verified yet
Editor Score 7.5/10

This six-piece mini notch is cut from 3/16-inch steel in a square-tube design. It adds some axle-to-frame clearance for street rods, mini trucks, and sport-dropped trucks. It is not meant for a frame-on-the-ground stance. Choose it for a moderate drop, weld it in, and skip it if you plan to slam the truck all the way down.

6 pieces
3/16″ steel
Weld-on
Square tube

Key Features

  • Six-piece weld-on set — A compact plate set that welds onto the frame rail for added axle clearance.
  • 3/16-inch steel — Listed thickness is solid for mild drops on light-duty daily trucks.
  • Square-tube design — A boxed profile suits straight rails, so confirm your frame shape before ordering.
  • Mini-truck focus — Marketed for street rods, hot rods, mini trucks, and sport-dropped pickups.

Pros

  • 3/16-inch plate thickness
  • Compact, simpler install

Cons

  • Not for deep or slammed drops
  • No rating data seen yet

🛒 Check Price on Amazon →

#5 BEST ENTRY-LEVEL MINI

5. labwork Universal Mini C Notch Kit — Axle-Flip Drops

Black metal frame notch kit with two curved notches for under bed suspension

★★★☆☆
3.2 on Amazon (5 ratings)
Editor Score 6.8/10

The labwork mini kit uses 3/16-inch steel in six weld-on pieces and gives modest clearance between axle and frame. It works best on axle-flipped sport drops. It carries the weakest rating here, 3.2 stars from five ratings, and ships without instructions. Buy it only if you can fabricate confidently and accept a few surprises along the way.

6 pieces
3/16″ steel
Weld-on
No instructions

Key Features

  • Six-piece weld-on set — Mini plate set designed to add a little room between axle and frame.
  • 3/16-inch steel — The listing describes weld-in construction for rigidity and long-term dependability.
  • Axle-flip friendly — Seller says it works well on axle-flipped sport drops, not extreme slams.
  • Professional install advised — No instructions are included, so plan for a fabricator or plenty of experience.

Pros

  • Low entry price
  • Suits light sport drops

Cons

  • Lowest rating in this list
  • No instructions included

🛒 Check Price on Amazon →

Buying Guide: How to Choose a Universal C Notch Kit for Lowered Trucks

Step notch kit plates laid out before welding for a lowered truck frame

Match the notch to your drop

Mini notches suit modest drops. Performance Online calls a rear frame C notch a must for air ride or for lowering a truck more than 4 inches. Beyond that point, choose a full-height step kit so the axle clears the frame without crushing bump stops.

Check the steel thickness

Plate thickness sets strength. The 5 mm kits run slightly thicker than 3/16-inch plate, while 10-gauge steel is thinner at just over 1/8 inch. Heavier plate tolerates welding heat and load better, but it takes longer to cut, fit, and finish.

Measure your frame rail

Universal rarely means universal. Rail height, width, and sweep change how a notch seats, and Roadkill Customs notes that finished notch depth varies with both. Measure your frame, then compare it to the kit dimensions before you cut anything, because a cut frame cannot be uncut.

Plan for boxing plates

A notch removes metal from a structural member. Boxing plates restore stiffness by welding to the upper and lower flanges of a C-channel rail, as Roadkill Customs shows in its step notch install. Confirm whether your kit includes them, or fabricate your own.

Think about travel and air ride

Notches pair well with air ride and coilovers, since those setups cycle the axle through more travel. Set the bags or springs so the axle clears the frame at full bump with some margin, and always leave room for the bump stops.

Prep the finish and hardware

Bare steel rusts fast under a truck. Budget for primer, paint, and cleaning supplies, plus a quality welder if you do the work yourself. Cutting discs and clamps add up quickly, so list every tool before you buy anything. Cheap tools cost more in rework.

Know your welding limits

Frame welding is structural work. If you are not confident, hire a fabricator. Check local rules too, since some states restrict frame modification and ride height. A budget kit welded badly costs more than a pricier kit welded right. Do not rush the fit-up.

Which C Notch Kit Fits Your Build?

  • Deep air-ride drops: Choose the PIT66 or airmaxxx for the tallest notch or the thickest plate.
  • Mid-height custom notch: Consider the BALOCEO, once you confirm what the seller actually ships.
  • Mild sport drops: The 3/16-inch six-piece mini kit adds modest clearance with a simpler install.
  • Tight budgets and experienced welders: Try the labwork, if you accept the 3.2 rating and missing instructions.
  • First-time welders: Skip all five and hire a fabricator, because frame work is a poor learning project.

How to Install a C Notch Kit: Overview

This is an overview, not a substitute for the kit maker’s instructions or a fabricator’s judgment. Follow these steps in order and keep the truck supported on proper stands the entire time.

  • 1. Mark the notch. Set the axle at full compression height, then trace the notch outline onto the frame rail.
  • 2. Bench-weld the notch. Fit and weld the plates off the truck, where you can reach every corner cleanly.
  • 3. Cut the rail. Remove the marked section with a reciprocating saw or cutting wheel, then deburr the edges.
  • 4. Fit and weld. Tack the notch in place, check alignment, then weld it to the rail’s upper and lower flanges.
  • 5. Box the frame. Weld boxing plates inside the rail to restore stiffness around the opening.
  • 6. Finish and align. Prime and paint bare steel, then book an alignment; our tire balance and alignment guide explains the order.
  • 7. Recheck clearance. Cycle the suspension through full travel and confirm the axle never touches the frame or bump stops.

Frequently Asked Questions

What is a C notch on a truck?

A C notch is a cutout in the frame rail above the rear axle. It lets the axle rise higher into the frame when a truck is lowered. Boxing plates then restore the rail’s strength around the opening.

Do I need a C notch for a small drop?

Usually not for small drops, though it depends on the truck. Retail guidance suggests drops beyond roughly 4 inches benefit from one. Check bump stop clearance at full compression before you decide to cut anything.

Mini notch or full step notch?

A mini notch gives modest clearance for mild sport drops. A full step notch, like the 10-inch PIT66, gives far more room. Choose by how low you plan to sit, not by price alone. Measure your rail either way.

Can I install one without welding?

The kits here are weld-in parts, so welding is part of the job. Bolt-in versions exist for some specific trucks. Hire a fabricator if you cannot weld structural steel with confidence. Always box the rails afterward.

Will a notch improve ride quality?

A notch adds axle travel, so the axle stops hitting the frame. It does not change spring rate. Ride quality still depends on springs and shocks, so see our KYB Excel-G review for shock options.

Is it legal to notch a truck frame?

Rules vary by state and inspection station. Many places care more about ride height and frame integrity than the notch itself. Check local regulations, ask your inspector before cutting, and keep photos of any professional boxing work.

Do I need a C notch with air ride?

Air ride lets you lay the frame on the ground, so a deep notch is common. Without one, the axle hits the frame when the bags dump. Plan notch depth around your lowest intended ride height.

Final Verdict

The best universal C notch kit for lowered trucks depends on how low you plan to sit. For deep drops, the PIT66 step kit and the 5 mm airmaxxx lead this list. The mini kits fit mild sport drops only. Match the kit to your frame and your skills, and the notch should do its job without drama.

Verify your frame dimensions, plan your boxing plates, and budget for welding and an alignment. Universal listings rarely guarantee fit, and several kits here lack ratings. Treat each one as raw material, not a finished solution.

Check current prices and ratings on Amazon before you buy. Thinking about lifting instead? Our Rough Country vs Superlift comparison covers it. Weld safely and drive low.

About Patrick Jordan

Patrick Jordan is an SAE Certified expert auto mechanic and car enthusiast with 10 years of practical experience. He has worked in some reputed garage in the USA That has helped him to gather more practical knowledge. Currently working at a major automotive startup company. Experienced in engine repair, vehicle upgrade, car interior, and exterior design management, off-road vehicle maintenance, etc. From reviews to expert solutions, you’ll find almost everything about automotive from him on AutoExpro.com
Follow me on
Twitter: Patrick Jordan
Facebook: Patrick Jordan
Pinterest:Patrick Jordan

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

  • Home
  • About Us
  • Contact Us
  • Privacy Policy
  • Affiliate Disclaimer
  • Terms and Conditions
  • Product Photographer
  • Advertising

COPYRIGHT © 2024 · AUTOEXPRO.COM, ALL RIGHTS RESERVED

AutoExpro is reader-supported. When you buy through links on our site, we may earn an affiliate commission. There is no additional cost to you. However, this does not impact our reviews and comparisons. We try our best to keep things fair and balanced to help you make the best choice.